Fractional CO2 Laser Resurfacing and Treatment

Fractional CO2 laser resurfacing is a gentle skin fix. It’s a hit for tackling stuff like wrinkles, acne scars, and droopy skin. This method is precise but powerful. It’s a great choice for people who want obvious skin upgrades without long downtime. The Fractional CO2 laser sparks more collagen in your skin. Plus, it’s not too heavy. You can wrap up a session fast and get back to your usual routine.

What Is the Fractional CO2 Laser?

The Fractional CO2 laser is a special carbon dioxide laser. It shoots light at a 10600nm wavelength. This device freshens up your skin. It handles issues like acne scars and aging marks. CO2 lasers send out light at 10600nm. Your skin’s water takes in this light. So, it softly strips away thin layers of skin from the surface and deeper spots. This kicks off your body’s own repair process.

How the Fractional CO2 Laser Works

In a Fractional CO2 laser session, a strong light at 10600 nanometers gets soaked up by water in your skin. This creates small paths in the treated spot. The skin nearby stays unharmed. Some warmth seeps into the tissue, tightening it up. It also heats the deeper skin layers. This pushes skin cells to make new collagen. Over weeks, your skin feels more elastic. You’ll notice fewer tiny lines and a softer surface.

The Fractional CO2 Laser Resurfacing Procedure

The treatment starts with a deep skin clean. Then, a numbing cream goes on to keep you cozy. You wait about an hour for the cream to kick in. After that, the session takes 30 to 60 minutes. The time depends on how big the area is. The laser glides over your skin in a tidy pattern. This makes sure every spot gets treated evenly.

Preparation

Before Fractional CO2 laser resurfacing, take some steps for top results. First, steer clear of the sun to avoid burns. Slather on a tough sunscreen with zinc oxide. It guards your skin from bad rays. Also, skip products like retinoids or scrubs. They might make your skin extra tender.

Healing and Aftercare

Healing differs for each person. Most see redness, puffiness, and flaking. These usually last 5 to 7 days. Use lotion to keep your skin hydrated and calm dryness. Wash your face softly to clear away dead skin. Keeping your skin safe from the sun is super important during this time. You’ll spot real changes in the weeks and months after the Fractional CO2 laser treatment.

Fractional CO2 Laser Treatment Benefits

This treatment brings lots of goodies for different skin needs:

• Wrinkle Reduction – It softens tiny lines and deeper grooves, like crow’s feet or forehead wrinkles.
• Scar Improvement – It works on acne scars, surgery marks, and stretch marks.
• Skin Texture & Tone – It cuts down sun damage, dark patches, and bumpy spots.
• Pore Minimization – It shrinks big pores for a sleeker look.
• Collagen Remodeling – It firms skin over time by building new collagen.

Also, the CO2 laser boosts collagen growth. This leaves your skin smoother, stretchier, and more even in color.

Can the CO2 Fractional Laser Remove Acne Scars?

It might not wipe out acne scars completely, but it does a lot. The Fractional CO2 laser treatment shines on moderate to bad acne scars. It dives deep into the skin where scar tissue is. Then, it grows new collagen. Over time, this fills in low spots and lightens dark marks.

Does the CO2 Fractional Laser Hurt?

You might feel a little weird during or after the session. But no worries. A numbing cream goes on first. After the treatment, it feels like a mild sunburn. You might sense some tightness or warmth. Basic care handles this. Over-the-counter pain pills and regular lotion usually help plenty.

FAQ

What is Fractional CO2 Laser Resurfacing?
It’s a skin fix using a carbon dioxide laser. It makes small, safe dots on your skin. This ramps up collagen growth. It boosts how your skin looks and feels. It also cuts down on lines and scars.

How does Fractional CO2 laser work?
The laser shoots focused light in a dotted pattern. It keeps nearby skin safe. This speeds up recovery. It also renews your skin.

What skin conditions can it treat?

• Tiny lines and wrinkles
• Acne and surgical scars
• Sun damage and dark patches
• Big pores
• Droopy skin and uneven texture

Is Fractional CO2 laser suitable for all skin types?
It’s good for lighter skin tones (Fitzpatrick I–III). For darker tones (IV–VI), the laser might need gentler settings. This stops dark or light spots.

How long does the procedure take?
Most sessions last 30–60 minutes. The time varies with the area’s size and treatment strength.

Is the procedure painful?
You might feel a bit of unease. Numbing cream or local pain relief is used first. Some feel a slight burn or tingle.

What is the recovery time?
Redness, puffiness, and light flaking last 5–7 days. Full healing and skin changes go on for 2–3 months. Downtime depends on laser settings and your skin’s sensitivity.

How many sessions are needed?
Many get nice results after 1–3 sessions. These are spaced 4–6 weeks apart. It depends on your skin and what you want.

Are there any side effects or risks?

• Short-term redness, puffiness, or flaking
• Slight unease or itching
• Dark or light patches (rare)
• Infection or scarring (super rare with good care)

What aftercare is required?
Keep your skin clean and moist. Stay away from the sun and use strong sunscreen. Don’t pick or rub the treated spot. Follow your doctor’s tips on creams or lotions.

Fractional CO2 Laser Resurfacing with Arfurla 10600nm Fractional Co2 Laser machine For Skin Resurfacing Rejuvenation

Arfurla brings top-notch tools with its Vertical 10600nm Fractional Co2 Laser machine. It’s built for beauty fixes like smoothing wrinkles and fading scars. The Arfurla 10600nm Fractional Co2 Laser For Skin Resurfacing Rejuvenation sends light at a 10600nm wavelength. This tightens skin tissue and warms deeper layers. It helps skin cells make new collagen.

This machine offers several perks:

1. Multi-functional: 3-in-1 system (Fractional+VRL+CO2) for different needs.
2. Quick session: Each treatment takes less than 30 minutes.
3. Works well: Awesome for women with loose vaginal areas and those with skin problems like acne scars.
4. No pain: Easy VRL procedure, in and out quick.

Other pluses include a user-friendly touchscreen for clinics. It also has a cooling system to keep patients comfy during treatments.

Contact Arfurla for distribution opportunities

Arfurla provides OEM/ODM services worldwide. They have their own research team and production setup. Arfurla is ready to offer OEM and ODM options to distributors everywhere. If you’re keen on sharing high-quality beauty tools like Fractional CO2 lasers, reach out at info@arfurla.com or call +86-1830-1023-578.

For questions about tech details or partnership chances:
Send your message here! We’ll share full technical info and a price quote!